|Payment Type:||T/T,D/P,Paypal,Money Gram,Western Union|
|Terms of Trade:||EXW|
|Delivery Time:||5 Days|
Model No.: WDM-SG300-1
Road Safety 300mm solar amber warning light
1. Product parameters
Product name: 300 type solar yellow flashing light
Number of lamp beads: 75
Product model: WDM-SG300-01
Product size: 350*350*130MM
Lamp beads category: Taiwan Epistar chip lamp beads
Yellow wavelength: 590-595NM
Working voltage: DC12V
Working temperature: -40℃-65℃
Solar Panel: 10W/18V
Battery: 7AH/12V, viewing distance: 1000M
Service life: 100000H
Shell material: PC
Beam angle: 30°
Protection level: IP53
Technical Solution for the Road Safety 300mm solar amber warning light
1. The solar yellow flashing lamp beads are made of condensing LEDs, and its LEDs are all using 5MM round head lamp beads, because the round head lamp beads belong to the condensing type LED, and the round head lamp beads are on the top The colloid is relatively high, and the colloid forms a light-gathering effect. This LED is basically used for traffic signal indicator lights. Our solar yellow flashing lights are also made of this LED, as shown in the figure.
2. The shell of the solar yellow flashing lamp is an environmentally friendly plastic shell, which is characterized by good chemical stability, good corrosion resistance to general acids and alkalis; good electrical insulation, which is a poor conductor and safe to use; It has good waterproof performance and is durable.
3. Reflective lens is installed on the solar yellow flashing lamp board. Because solar yellow flashing lights are powered by solar energy, it is necessary to do more than supply to ensure that they work properly. This is the commonality of solar products. In order to make the brightness of the entire solar yellow flash lamp higher under the same current situation, a retro-reflective lens must be installed. Under the same current situation, a retro-reflective lens should be installed to improve the brightness. Times!
4. Solar panel, solar yellow flashing solar panel is made of single crystal silicon material, which is a relatively active non-metallic element, with high purity and high efficiency of solar energy conversion rate, and most of the use of amorphous silicon, polycrystalline silicon Compared with the product, the Monocrystalline Silicon Solar Panel has excellent endurance and high photoelectric conversion rate, which can make the yellow flash lamp work longer in continuous rainy weather.
Features of Road Safety 300mm solar amber warning light:
1. Green energy, economic and environmental protection, no harmful substances, no pollutants.
2. The LED adopts Taiwan Epistar chips, with a service life of ≥100000 hours, high brightness, unique optical system, uniform chromaticity, good warning effect, and slow light attenuation.
3. Low power consumption, large viewing angle, super high brightness, long viewing distance and long working time.
4. Sturdy and durable. Stable and reliable, high protection level. Impact resistance, aging resistance, corrosion resistance.
5. Waterproof. Easy to install.
6. Comply with GB/14887-2003 and relevant international standards
Installation of Road Safety 300mm solar amber warning light:
This product should be installed vertically, pay attention to the sun hat on the upper part of the lamp and the outlet hole facing down. The installation steps are as follows:
1. There is a screw on both ends, unscrew the nut above the screw,
2. Put the flat end of the "L" type bracket on the screw according to the hole position and the slot, then put the bracket of the solar panel into the screw on the upper end of the lamp, put the gasket and nut, and tighten the nut. Then, the butt joint of the solar panel and the butt joint of the lamp can be docked. (as the picture shows)
3. The sun visor is installed on the upper part of the lamp. Fold the 3-corner aluminum plate into a circular arc shape, put it on the lamp, and tighten it with the screw to the corresponding hole position. (as the picture shows)
4. Make two holes in the signal light pole, drill holes according to the signal L-bracket position, use a suitable screw to pass through the light pole, and put the L-shaped bracket on the screw and fix it with the nut. (as the picture shows)
300mm yellow flashing light wiring instructions
The solar yellow flashing lights can be set to night mode and 24-hour mode. Two switches are used to control the entire solar yellow flashing light. One is that the main switch controls the entire light to not work or turn on the work. The other switch is the solar light control mode. The red switch is the main switch, and the black switch is the light control switch. The light control switch refers to whether you choose 12-hour mode or 24-hour mode.
Product packaging for the Road Safety 300mm solar amber warning light
7. Field application for the Road Safety 300mm solar amber warning light
In addition to One Aspect 300mm Red Traffic Signal Light, We also produces other traffic lights:
1. Traffic lights at crossroads
2. Integrated traffic lights
3. Mobile traffic lights
4. Solar traffic lights, etc.